通过认证
“RIMET纳米喷雾机-P400”参数说明
| 是否有现货： | 是 | 加热类型： | MCH |
| 应用： | 均可 | 显示屏类型： | LED |
| 材料： | 铝 | 用途： | 美容美发 |
| 型号： | P400 | 规格： | 1 |
| 商标： | RIMET | 包装： | 94*35*35cm |
| 产量： | 10000 |
“RIMET纳米喷雾机-P400”详细介绍
操作简介(operating instructions)
1.从注水口往水箱加干净的软化水（如纯净水，蒸馏水）。
Please water the clean water (such as pure water, distilled water ) to the water tank (from the water inlet).
2.检查电源是否安全连接，打开机器侧板上的电源开关。
Check whether the power supply is safe connection, turn the switch on the machine side.
3.机器初始设定默认为：时间15分钟， 时间设定最高30分钟。
The initial setting time of the machine: 15 minutes, max time 30 minutes
4.按下启动键，机器自检，往纳米发生器里面抽水，开始预热（约需3分钟）。
Press the start button, the machine self-testing, draw water to the nano generator inside, began to preheat (about 3 minutes).
5.加热完成后，有“嘀”提示，工作指示灯（右）由红色变为绿色。
After the heating, there are "Di" sound, work lights (right) from red to green.
6.按下喷气手柄内侧开关，开始/暂停 喷雾。时间可以按需要随意调节。
Press the switch of jet handle inside, start / stop spray. Time can be adjusted as required.
7.缺水提示：水箱里面水位过低时，机器将自动停止工作，水位指示灯（左）红色闪亮，并有报警“滴滴”声。时间显示窗显示E6，往水箱添加足够量水即可恢复正常工作。（加水时注意观察水位，避免过量加水造成溢出）
Water shortage: the water level in the tank is too low, the machine will automatically stop working, the water level indicator light (left) red flashing, and there is alarm "di-di" sound. Time window to display the E6, add enough water to the water tank,it can resume normal work. (pay attention to the water level when adding water, avoid excessive water overflow)
8.排水清洁保养(drainage cleaning and maintenance)：
A纳米发生器排水：停机10分钟，待纳米发生器冷却降压后，打开排水龙头，直接排放。（注意高温，小心烫伤）
A nano generator drainage: stop to use the machine 10 minutes, after the nano generator cooling down, open the drainage bibcock, direct emissions (pay attention to high temperature, avoid to scald)
B储水箱排水：打开机器底部水箱排水龙头，即可将水箱里面的水排出。
B Storage tank drainage: Open the tank drain tap at the bottom of the machine . You can pour out off water the tank .
1.从注水口往水箱加干净的软化水（如纯净水，蒸馏水）。
Please water the clean water (such as pure water, distilled water ) to the water tank (from the water inlet).
2.检查电源是否安全连接，打开机器侧板上的电源开关。
Check whether the power supply is safe connection, turn the switch on the machine side.
3.机器初始设定默认为：时间15分钟， 时间设定最高30分钟。
The initial setting time of the machine: 15 minutes, max time 30 minutes
4.按下启动键，机器自检，往纳米发生器里面抽水，开始预热（约需3分钟）。
Press the start button, the machine self-testing, draw water to the nano generator inside, began to preheat (about 3 minutes).
5.加热完成后，有“嘀”提示，工作指示灯（右）由红色变为绿色。
After the heating, there are "Di" sound, work lights (right) from red to green.
6.按下喷气手柄内侧开关，开始/暂停 喷雾。时间可以按需要随意调节。
Press the switch of jet handle inside, start / stop spray. Time can be adjusted as required.
7.缺水提示：水箱里面水位过低时，机器将自动停止工作，水位指示灯（左）红色闪亮，并有报警“滴滴”声。时间显示窗显示E6，往水箱添加足够量水即可恢复正常工作。（加水时注意观察水位，避免过量加水造成溢出）
Water shortage: the water level in the tank is too low, the machine will automatically stop working, the water level indicator light (left) red flashing, and there is alarm "di-di" sound. Time window to display the E6, add enough water to the water tank,it can resume normal work. (pay attention to the water level when adding water, avoid excessive water overflow)
8.排水清洁保养(drainage cleaning and maintenance)：
A纳米发生器排水：停机10分钟，待纳米发生器冷却降压后，打开排水龙头，直接排放。（注意高温，小心烫伤）
A nano generator drainage: stop to use the machine 10 minutes, after the nano generator cooling down, open the drainage bibcock, direct emissions (pay attention to high temperature, avoid to scald)
B储水箱排水：打开机器底部水箱排水龙头，即可将水箱里面的水排出。
B Storage tank drainage: Open the tank drain tap at the bottom of the machine . You can pour out off water the tank .
